Факультет електромеханіки та електрометалургії (ІПБТ) <br> Інститут промислових та бізнес технологій (ІПБТ)
Permanent URI for this community
UK: Факультет електромеханіки та електрометалургії (ІПБТ)
Інститут промислових та бізнес технологій (ІПБТ) EN: Faculty of Electromechanics and Electrometallurgy
Institute of Industrial and Business Technologies
Інститут промислових та бізнес технологій (ІПБТ) EN: Faculty of Electromechanics and Electrometallurgy
Institute of Industrial and Business Technologies
Browse
Browsing Факультет електромеханіки та електрометалургії (ІПБТ) <br> Інститут промислових та бізнес технологій (ІПБТ) by Issue Date
Now showing 1 - 20 of 144
Results Per Page
Sort Options
Item One Approach to Quasi-Optimal Control of Direct Current Motor(IEEE (Institute of Electrical and Electronics Engineers), 2019) Tryputen, Mykola; Kuznetsov, Vitaliy; Serdiuk, Tetiana M.; Kuznetsova, Alisa; Tryputen, Maksym; Babyak, Mykola O.ENG: The article presents the calculation of the transfer function of the DCM-30-N1-0.2 micromotor DC, obtained a transcendental system of equations for determining the duration of the quasi-optimal control intervals and the dependence of the first control interval on the specified overshoot. The obtained dependence can be used in the engineering methodology for the synthesis of quasi-optimal control and the choice of actuators of the automatic control system.Item Improvement of Technical Service of Track Circuits(Institute of Electrical and Electronics Engineers, IEEE, 2019) Serdiuk, Tetiana M.; Kuznetsov, Vitaliy; Serdiuk, Kseniia; Nikolenko, Anatoliy; Kuznetsova, Yevheniia; Kuznetsova, AlisaENG: The automated method of measuring the time and amplitude parameters of code current and parameters of track circuits (input impedance of the track circuit, a characteristic impedance, a propagation constant) were elaborated. The mathematic model of track circuits’ channel of transferring code current was improved and considered in this paper. The algorithms of definition of parameters of track circuit are offered.Item Mathematical Model of Dynamics of Homomorphic Objects(Petro Mohyla Black Sea National University, Mykolaiv, 2019) Kuzenkov, Olexandr; Serdiuk, Tetiana M.; Kuznetsova, Alisa; Tryputen, Mykola; Kuznetsov, Vitaliy; Kuznetsova, Yevheniia; Tryputen, MaksymENG: Abstract. The paper concerns topical problem of mathematical modeling of dynamics of heterogeneous groups with a logistic function as a basic one. Joint use of mathematical models of biological systems and computer-based simulation makes it possible to minimize time and save material resources while determining general tendencies of subpopulation progress; and to forecast state of the system as well as possible consequences of artificial intervention in the environment. Among other things, it concerns forecasting of genetic abnormalities. The paper proposes a model of dynamics of progress of a population consisting of n subpopulations. The model is represented in the form of differential equations with transition coefficients within their right sides. The transition coefficients mirror the share of species getting from ith subpopulation to jth one. The proposed system is not Voltairian one since its phase trajectories may cross coordinate axes. It has been proved that the system of differential equations is degenerated in the neighbourhood of equilibrium points. Analysis of the system of differential equations for n=2 has demonstrated a potential for three bifurcations. It has been proved that nine bifurcation types are possible for n=3. Numerical computer-based experiments have shown that the proposed model is stable as for the disturbance of its coefficients, and the obtained characteristics of the degenerated system are close to real ones.Item Improving the Reliability of Simulating the Operation of an Induction Motor in Solving the Technical and Economic Problem(Springer, Cham, 2020) Tryputen, Mykola; Kuznetsov, Vitaliy; Kuznetsova, Alisa; Tryputen, Maksym; Kuznetsova, Yevheniia; Serdiuk, Tetiana M.ENG: The article is devoted to the control of the statistical laws of linear voltages reproduced on a computer during computational studies on an energy-economic model when solving the problem of choosing protection tools for induction motors operating in workshop electric networks of industrial enterprises with low-quality electricity. Simultaneous and continuous estimation of average values, variances, autocorrelation and cross-correlation functions of harmonics of linear voltages is based on the adaptive approach. The article presents mathematical expressions for correcting the values of statistical quantities with the accumulation of information and proposes structural schemes for a comprehensive analysis of the results of reproduction of random variables and functions on a computer. The results of checking the values of the average values and dispersions of six harmonics of simulated linear voltages supplying an induction motor with a power of 7.5 kW are shown for the conditions of the rolling shop No. 1 of Dneprospetsstal LLC.Item Development of a Method of Calculating the Temperature of a Survey Assembly When Preparing a Train Dispatch(Львовский политехнический национальный университет, Львів, 2020) Ustymenko, Dmytro V.; Kuznetsov, Vitaliy; Marenych, Oksana L.; Kovzel, Maksim; Mukha, Andrii M.; Sinkevych, Oleksiy; Tryputen, Mykola; Al Said Ahmad, Mohammad Ahmad DiabENG: The features of the thermal state of the current collection unit «contact wire – contact insert of the current collector» in the conditions of preparation of electric rolling stock for the journey are considered. As part of the study, a methodology has been developed for estimating the heating temperature of the power sliding contact zone in the conditions of train preparation for journey. Application of the method will help to reduce the number of «burnouts» of the contact wire due to the exact selection of the heating/cooling time of the train for a certain heating/conditioning current when preparing the electric rolling stock for the journey. It was established that the cause of the «burns» of the contact wire in the parking lots when preparing the train dispatch is the excess of the permissible temperature of the power sliding contact as a result of the prolonged action of the heating/conditioning current. The standard approach for determining the duration of heating is based on the average values of the loads on the system and therefore does not take into account some factors, for example, the state of the contact wire, the state of the contact insert of the current collector, the number of cars in the train, and so on. The proposed technique is based on the classical theory of electrical contact and the theory of heating a homogeneous body, which makes it possible to accurately assess the thermal state of the power sliding contact and convenient enough for use in operating conditions. The results of the work are of practical value, since the technology of preparing a train for dispatch can be supplemented by calculating the contact temperature «contact wire element – contact insert element» in accordance with the proposed methodology. This will allow for a specific train in specific conditions to apply a set of measures to prevent «burnout» of the contact wire in the event of a possible temperature exceeding the permissible value.Item Вплив піщано-рідкоскляних форм, структурованих паро-мікрохвильовим затвердінням, на пригар і шорсткість поверхні виливків(Фізико-технологічний інститут металів і сплавів Національної академії наук України, Київ, 2021) Солоненко, Людмила Ігорівна; Реп’ях, Сергій Іванович; Білий, Олександр ПетровичUKR: Метою цієї роботи є вивчення впливу піщано-рідкоскляних форм, структурованих за способом паро-мікрохвильового затвердіння (ПМЗ-процес), на пригар і шорсткість виливків. У дослідженнях використовували форми, що були виготовлені за Сold-box-amin-процесом, Resol-CO2-процесом, СО2-процесом та ПМЗ-процесом, які заливали сталлю 30Л. Зразки виливків зі сталей 30Л, 20Х27Н18С2Л, сірого чавуну СЧ20, бронз БрА9Ж3Л, БрО5Ц5С5, БрО4Ц4С17 і алюмінієвого сплаву АЛ2 відливали в форми, що виготовлені за ПМЗ-процесом. Перегрів всіх сплавів над температурою ліквідус при заливці становив 120 ± 7 °C. Мікроструктуру зразків сталі 30Л досліджували на оптичному мікроскопі МБС-10 до і після їх травлення ніталем. Параметри шорсткості визначали на профілометрі в комплекті з інформаційно-обчислювальним комплексом мод. 170622. Встановлено, що якість поверхні виливків, виготовлених за ПМЗ-процесом, не поступається якості поверхні виливків, виготовлених в формах за Сold-box-amin, Resol-CO2, СО2-процесами, і для виливків зі сплаву АЛ2 знаходиться на рівні якості (по чистоті поверхні) з виливками, що виготовляють в оболонкових формах. Якщо врахувати, що ПМЗ-процес екологічно безпечніший, ніж Сold-box-amin, Resol-CO2-процес, і економічніший, ніж Сold-boxamin, Resol-CO2 і СО2-процес, то цей спосіб виготовлення форм і стрижнів, з числа перерахованих способів, при наявності відповідного обладнання та оснащення, є найбільш перспективним для виготовлення середнього і дрібного литва загальномашинобудівного призначення із залізовуглецевих і легкоплавких кольорових сплавів. Виходячи з викладеного, перспективні дослідження повинні бути спрямовані на встановлення закономірностей впливу ряду основних параметрів плакованих рідкоскляних сумішей і умов виготовлення форм і стрижнів за способом ПМЗ на якість литва та оптимізацію умов структурування подібних сумішей в умовах виробництва виливків в сучасних ливарних цехах.Item Корозійна стійкість бронзових виробів(Національна металургійна академія України, Дніпро; Технічний університет м. Варна, Болгарія, 2021) Кімстач, Тетяна Володимирівна; Узлов, Костянтин Іванович; Усенко, Руслан Вікторович; Солоненко, Людмила ІгорівнаUKR: На сьогодні все більш широке застосування в різних галузях промисловості знаходять сплави на основі міді. Це пояснюється поєднанням високої корозійної стійкості таких сплавів в різних середовищах з високими ливарними властивостями, здатністю до пластичної деформації, високої електро- і теплопровідності, тощо. У зв'язку з цим певний науковий і практичний інтерес представляє визначення базових положень які забезпечують бронзам потрібний рівень корозійної стійкості в середовищах різних складів (при різних умовах експлуатації). За результатами аналізу встановлено, що завдяки сукупності високої корозійної стійкості, конструкційної міцності та експлуатаційної надійності, найбільш широке застосування в промисловості знайшли алюмінієві бронзи. Ці сплави найчастіше застосовують в обладнанні, де завдяки стійкості до корозії, вони мають перевагу в порівнянні, наприклад, з олов'яними і крем'янистими бронзами. Істотним фактором, що визначає корозійну стійкість алюмінієвих бронз, є їх структура. При цьому сплави, які складаються тільки з α-фази, мають більш високу корозійну стійкість, в порівнянні з двофазними сплавами.Item Analysis of the Neutral Grounding Modes Influence on the Reliability Characteristics of Local Systems with Renewable Energy Sources(Polskie Towarzystwo Diagnostyki Technicznej, Warszawa, 2021) Ostapchuk, Oleksandr; Kruczek, Włodzimierz; Kuznetsov, Valeriy; Kuznetsov, Vitaliy; Tsyplenkov, DmytroENG: When comparing the performance indicators of electrical networks with different types of neutral grounding, along with the fulfilment of the requirement to ensure reliability of power supply to consumers, serious attention is drawn to the main network parameters influencing the performance of power supply systems. Analysis of research and its results, reported above, on the influence of the neutral ground of power networks on the reliability and electrical safety conditions of the power supply systems as a whole, on the damage of distribution networks and electrical equipment as well as on the working capacity of relay protection devices, provides an opportunity to estimate each specific operation mode of the neutral and to develop recommendations aimed at strengthening the positive indicators of the corresponding modes. Other things being equal, reliability of power supply to electrical receivers or reliability of distribution networks is mainly determined by the damage to network elements and the performance of relay protection devices. The degree of influence of these factors on the reliability of distribution networks depends on the neutral mode, which in turn determines the level of overvoltages and the nature of transient processes at ground failure.Item Кулястий графіт в заевтектичному чавуні(НМетАУ, Дніпро, 2021) Іванова, Людмила Харитонівна; Колотило, Євген ВікторовичUKR: Мета. Дослідження розподілу гадолінію в структурних складових валкового чавуну. Методика. Для дослідження впливу гадолінію на структурні складові плавку проводили в силітовій печі. Розплав чавуну перегрівали і методом примусового занурювання оброблювали зростаючими кількостями металевого гадолінію. Зразки охолоджувалися зі швидкістю, яка є в осерді реальної валкової ливарної форми – 0,5 град/c. Металографічний аналіз проводили на металомікроскопі моделі Neophot 21, рентгеноспектральний мікроаналіз проводили на установці MS-46 за прискорювального напругу 20 кВ і струму зонда 25 нА на зразках, виплавлених в індукційній печі ВЧИ-10 з охолодженням сплаву зі швидкістю 10 град/хв. Результати. Лабораторними дослідженнями були встановлені залишкові вмісти гадолінію в чавуні серцевини і шийок валків, що забезпечують отримання кулястого графіту з фактором форми 0,8...0,9. Визначено, що гадоліній зосереджений в основному в оболонці графітного включення, прилеглої до його центрального ядра. Після статистичної обробки результатів встановлено, що вміст гадолінію в центральному ядрі графітного включення – 0,015%. Встановлено, що розподіл гадолінію носить подібний з ітрієм характер, а в порівнянні з церієм – зворотний характер. Наукова новизна. Вперше проведено аналіз розподілу гадолінію в кулястому графіті заевтектичного чавуну. Практична значущість. Визначення ролі модифікатора в процесі формоутворення графіту дозволить створити найбільш ефективні модифікатори і розробити раціональну технологію отримання чавуну з кулястим графітом. Результати роботи будуть використані при виготовленні литих прокатних валків із комплексно модифікованих чавунів.Item Electrotechnical Materials(RS Global, Warsaw, Poland, 2021) Tsyplenkov, Dmytro; Nikolenko, Anatolii; Kolb, Andrii; Grebeniuk, Andrii; Kuznetsov, Vitalii; Babyak, Mykola O.; Kovalenko, ViktorENG: The regularities of processes and phenomena that occur in dielectric, conductive, semiconductor and magnetic materials as part of electrical and electronic devices under the influence of energy of electric, magnetic and thermal fields are considered. The main feature of the textbook is a detailed structuring of educational material, focusing largely on the distance form of learning, as well as demonstration of the close relationship of the properties of various electrical materials and the basics of electrical engineering on specific examples. The manual is intended for students of specialties: 141 - "Electrical Energetics, Electrical Engineering and Electromechanics" and 275 - "Transport technologies", as well as for students of other specialties of higher education, which are related to the study of disciplines of electrical engineering and electronic computer science.Item Розрахунок кінетики просування фронту кристалізації ізосолідус залізовуглецевих сплавів у кокільних циліндричних формах(Фізико-технологічний інститут металів та сплавів НАН України, Київ, 2021) Семенов, О. Д.; Хричиков, Валерій Євгенович; Куцова, Валентина Зіновіївна; Меняйло, Олена ВалеріївнаUKR: Мета роботи – оцифрування експериментальних термографічних вимірів процесів твердіння в кокілі циліндричних виливків із залізовуглецевих сплавів, їх інтерполяція для діапазону вмісту вуглецю 0,1...4,83 % і розробка графоаналітичної методики побудови кінетики просування фронту ізосолідус. Сучасні аналітичні розрахунки твердіння і охолодження виливків методом інтегрального теплового балансу Стефана-Шварца, А. І. Вейника, М. І. Хворінова не дозволяють встановити вплив хімічного складу сплаву, повітряного зазору між затверділим шаром металу і кокілем, ступінь чорноти поверхні, розширення кокілю при нагріванні, усадки метала виливка та залежність теплофізичних коефіцієнтів від температури. Програми комп’ютерного моделювання процесів затвердіння підвищують точність розрахунків тільки за умови адаптації з результатами експериментальних вимірювань температур твердіння виливків, що мають конкретний хімічний склад. В роботі оцифровано результати дев’яти експериментальних досліджень процесів твердіння циліндричних виливків зі сплавів Fe-C, отримані Б. Б. Гуляєвим, О. Н. Магницьким, Л. М. Постновим в координатах параметричного критерію (τ/R2) і відносної товщини (х/R) затверділого шару металу (х). Отримані залежності кристалізації 100 % твердої фази з кроком 0,05 х/R інтерполювали в діапазоні вмісту вуглецю 0,04...4,83 %. Наведено приклади розрахунку тривалості твердіння циліндричних виливків різних хімічних складів, а за гіпотезою приведеної товщини М. І. Хворінова можливо встановити в першому наближенні тривалість затвердіння виливків у формі куля і плита. Отримані результати рекомендовано використовувати для оцінки точності комп’ютерного моделювання процесів затвердіння еталонних сплавів Fe-C і подальшого корегування теплофізичних коефіцієнтів, які взято в розрахунках. Побудовано кінетику просування фронту ізосолідус для сплаву Fe-0,3%C, який охолоджується в циліндричній виливниці, розрахована його загальна тривалість затвердіння. Використовуючи графіки в координатах τ/R2 і х/R можна розрахувати тривалість кристалізації виливків різних розмірів, мінімальний час безпечного переміщення виливниці зі злитком з кесона до ділянки охолодження виливків для виконання технології гарячого посаду злитка в термічну піч, реалізувати технологію впливу на рідкий метал в ливарній формі або газодинамічного тиску в процесі кристалізації рідкої фази.Item Rational Integration Level of Solar Generation in Traction Power Supply Substations for Supplying Auxiliary Consumers(Kaunas University of Technology, Lithuania, 2021) Kuznietsov, M.; Kuznetsov, Valeriy; Ostapchuk, O.; Kuznetsov, Vitaliy; Hubskyi, Peter V.ENG: The paper considers the existing levels of electricity consumption by responsible consumers of gas and evaluates the use of solar generation to meet these needs. Using mathematical modeling based on real statistics, the dependences of solar power on the time of day are determined, which allows to estimate the random component of solar generation and determine the possibility of compensating the variability by using AB. The method of choosing the optimal capacity of the battery, taking into account the stochastic nature of solar generation is presented.Item Efficient Algorithms for Parallelizing Tridiagonal Systems of Equations(НМетАУ, Дніпро, 2021) Shvachych, Gennady Grygorovych; Vozna, Nataliіa; Ivashchenko, Olena Valerievna; Bilyi, Oleksandr; Moroz, DmytroENG: The article is devoted to the development of the maximal parallel forms of mathematical models with a tridiagonal structure. The example of solving the Dirichlet and Neumann problems by the method of straight lines and the sweep method for the heat equation illustrates the direct fundamental features of constructing parallel algorithms. It is noted that the study of the heat and mass transfer processes is run through their numerical modeling based on modern computer technology. It is shown that with the multiprocessor computing systems’ development, there disappear the problems of increasing their peak performance. On the other hand, building such systems, as a rule, requires standard network technologies, mass-produced processors, and free software. The noted circumstances aim at solving the so-called big problems. It should be borne in mind that the classical approach to solving the tridiagonal structure models based on multiprocessor computing systems is far more time-consuming compared to single-processor computing facilities. That is explained by the recurrence relations that make the basis of classical methods. Therefore, the proposed studies are relevant and aim at the distributed algorithms development for solving applied problems. The proposed research aims to construct the maximal parallel forms of mathematical models with a tridiagonal structure. The paper proposes the schemes to implement parallelization algorithms for applied problems and their mapping to parallel computing systems. Parallelization of tridiagonal mathematical models by the method of straight lines and the sweeping method allows designing absolutely stable algorithms with the maximum parallel form and, therefore, the minimum possible time for their implementation on parallel computing devices. It is noteworthy that in the proposed algorithms, the computational errors of the input data are separated from the round-off errors inherent in a PC. The proposed approach can be used in various branches of metallurgical, thermal physics, economics, and ecology problems in the metallurgical industry.Item Дослідження кінетики азотування мало- та безнікелевих корозійностійких сталей в твердому стані(НМетАУ, Дніпро, 2021) Пройдак, Юрій Сергійович; Підгорний, Сергій Миколайович; Трегубенко, Геннадій Миколайович; Поляков, Георгій Анатолійович; Палаш, Богдан ВалерійовичUKR: Мета. Дослідження кінетики азотування в твердому стані прокату з мало- та безнікелевих корозійностійких сталей на усю товщину для отримання стійкої аустенітної структури. Методика. Азотування зразків проводилося у вакуумній печі при температурах 1200-13500С при витримках від 2-х до 30-ти годин. Температуру заміряли платино-платинородієвою термопарою з точністю до +100С. В процесі нагріву зразків тиск азоту підтримували постійним. Після витягання зразків з печі виконували їх аналіз: рентгеноструктурний, пошаровий, металографічний та хімічного складу, у тому разі на вміст азоту. Результати. Результати проведеної роботи свідчать про принципову можливість азотування Сr-Мn і Сr-Мn-Ni сталей в твердому стані після їх гарячої деформації з відносно невеликою тривалістю процесу при товщині прокату до 7 мм. Наукова новизна. Вперше проведені дослідження кінетики азотування корозійностійких сталей Х15Г12 та Х18Н4Г10 в твердому стані при температурах 1200-13500С. Практична значущість. Застосування технології азотування мало та без нікелевих корозійностійких сталей в твердому стані значно підвищує їх якість та знижує їх собівартість.Item Тривалість нагріву та випаровування води з парних наважок масою до 100 г мікрохвильовим випромінюванням(Scientific Publishing Center “Sci-conf.com.ua”; SSPG Publish, Stockholm, Sweden, 2021) Солоненко, Людмила Ігорівна; Реп’ях, Сергій Іванович; Мазорчук, Володимир ФедоровичUKR: У роботі досліджується вплив маси та місця положення наважок води масою до 100 г на тривалість їх нагрівання та випаровування. Встановлено взаємний вплив парних наважок води розташованих як на краю, так і в центрі робочого столу мікрохвильової печі. При цьому, зі збільшенням маси однієї наважки зростає і тривалість нагрівання та випаровування води з іншої наважки. В області малих мас наважок характер їхнього взаємного впливу змінюється і коли сумарне значення мас наважок води не перевищує 140 г, їх час випаровування прагне до однакових значень.Item Corrosion Resistance of Reinforced Layers of 15х11МФ Steel Steam Turbine Blades(Національний науковий центр «Харкiвський фiзико-технiчний інститут», 2021) Hlushkova, D. B.; Bahrov, V. A.; Hrinchenko, O. D.; Hnatiuk, A. A.; Kalinina, N. E.; Kalinin, V. T.ENG: The reliability of the vane apparatus of steam turbines largely determines the operation of the turbine as a whole. The results of scientific research indicate that the surface operation of the blades in the wet-steam flow is caused by a combination of corrosion and drip erosion. The presence of chemical elements and compounds in the working fluid intensifies the process of blade wear. The pH value of the working environment, which can fluctuate significantly during operation, has a significant effect on the wear characteristics. The influence of methods of strengthening the leading edges of steam turbine blades made of steel is analyzed 15H11MF on corrosion resistance. Corrosion tests of blade samples were carried out, the inlet edges of which were strengthened in three ways: high current amplification, electrospark alloying with T15K6 alloy, electrospark alloying with steel 15H11MF. According to the results of the tests, the layer strengthened by hardening by high-frequency currents has the lowest corrosion rate, the layer strengthened by electrospark alloying with T15K6 hard alloy has the highest. The corrosion rate of the layer reinforced by electrospark alloying of steel 15H11MF is 2.1 less than that of the layer reinforced with T15K6 alloy.Item Complex of Mathematical Models and Methods to Calculate Pressure Effect on Sulfide Distribution in Steel(Хмельницький національний університет, Україна, 2021) Selivyorstova, Tetjana V.; Selivyorstov, Vadim Yu.; Kuznecov, Vitaliy V.ENG: Primary objective is to develop computational method to analyze digital pictures of sulfide prints, helping obtain qualitative image characteristics, and to formulate mathematical model of the distribution of sulphide inclusions to determine specific features of the pressure effect on the macrostructure formation of carbon steel castings flooded into the uncooled mold. The research was carried out using images of sulfide prints of templates cut of steel cylindrical castings; L500 steel was applied. The castings result from industrial tests of a method of gas-dynamic effect on the fusion in the foundry forms under the conditions of a casthouse of Dnipropetrovsk aggregate plant PJSC. Digital pictures of sulfide prints, obtained in terms of the increased rate of gas pressure and maximum pressure, were binarized; defective fra gments were removed; and zo ning took place. The developed computational method has been applied for fragments of images, representing different zones; data arrays have been received containing sizes and amounts of inclusions in the fragment. The developed computational method to analyze digital images of sulfide prints has been implemented. ASImprints software support has helped obtain qualitative characteristics of images; namely, distribution of amount of the certain-size sulfide inclusions. The computational method to analyze digital images of sulfide prints has made it possible to study the set of patterns of sulfide prints. The dependences have been obtained, describing specific features of sulfide inclusion distribution while varying gas-dynamic pressure method in terms of fusion in the casting form. It has been demonstrated that the distribution describes effectively the power-series distribution to compare with the exponential one. Mathematical model of the power -series distribution parameter dependence upon pressure has been developed. Deviation of the distribution parameters in terms of the experimental values and the model values has been evaluated. The research demonstrates the ways to apply an algorithm of simple recursive casting for quantitative analysis of digital images of sulfide prints. Use of ASImprints, being software implementation of the computational method to analyze digital images of sulfide prints making it possible to obtain qualitative characteristics of images, has helped identify that the increased pressure within a casting-device for gas injection system results in the increased specific amount of inclusions and the decreased specific zone of sulfide inclusions respectively. It has been defined that exponential function describes reliably the nature of sulfide inclusion distribution in the digital image of sulfide print. The research has demonstrated that fragments of a sulfide print, belonging to one zone, are statistically homogeneous. Thus, it is possible to analyze quantitively digital image zone of a sulfide print on its fragment. Mathematical model of dependence of sulfide inclusion distribution in carbon-steel castings in terms of gas-dynamic effect on fusion solidifying in a mold has been developed. The model may be applied to predict sulfide inclusion distribution within the selected zones of cross section of the cylindrical castings solidifying in the uncooled mold in terms of the preset mode of gas-dynamic effect.Item Вплив розмірів та положення наважок води на обертовому столі мікрохвильової печі на тривалість їх випаровування(Scientific Publishing Center “Sci-conf.com.ua”; SSPG Publish, Stockholm, Sweden, 2021) Солоненко, Людмила Ігорівна; Реп’ях, Сергій ІвановичUKR: У роботі досліджується характер зміни та ступінь впливу потужності мікрохвильового випромінювання від радіусу видалення точкової та великої наважки від центру осі обертання обертового столу мікрохвильової печі. Встановлено, що характер зміни потужності мікрохвильового випромінювання від радіусу видалення як точкової, так і великої наважки ідентичний і носить статечний характер. Відмінність у ступені впливу віддалення від осі обертання мікрохвильової печі на зміну інтенсивності нагріву наважок зумовлено як їх габаритними розмірами, так і відстанню від осі обертання робочого столу мікрохвильової печі. Найбільш інтенсивне нагрівання відбувається при положенні наважок на відстані від 70 до 110 мм від центру обертання робочого столу використовуваної мікрохвильової печі, при цьому інтенсивність зростає при зменшенні габаритних розмірів самої наважки.Item Моделювання впливу технологічних факторів на процес утворення газової пористості у відливках з вторинних алюмінієвих сплавів(НМетАУ, Дніпро, 2021) Трегубенко, Ганна Василівна; Меняйло, Олена ВалеріївнаUKR: Мета. Дослідити вплив різних технологічних факторів на процес газовиділення водню при кристалізації вторинних алюмінієвих сплавів. Методика. Виконано моделювання процесу утворення газової пористості у відливках із вторинних алюмінієвих сплавів. Результати. Визначено, що для пізнішого виділення водню в газові бульбашки при затвердінні алюмінію та його сплавів необхідно підвищувати ступінь пересичення твердого металу воднем, зменшувати вихідний вміст водню в розплаві, підвищувати щільність і поверхневий натяг розплаву, збільшувати роботу утворення зародка газової бульбашки. Встановлено, щоб знизити інтенсивність виділення водню в газові бульбашки при затвердінні вторинних алюмінієвих сплавів потрібно зменшувати швидкість кристалізації та ступінь пересичення розплаву воднем. Наукова новизна. Вперше отримано математичну модель для прогнозування газовиділення водню в процесі затвердіння вторинних алюмінієвих сплавів. Практична значущість. Результати роботи можна застосовувати при виробництві конструкційних вторинних алюмінієвих сплавів для оптимізації технологічного процесу та мінімізації кількості газових пор та їх розмірів, а також отримання закритої газової пористості навіть після термо- або механічної обробки. Крім того, використання на практиці отриманих виразів дозволяє при отриманні литих алюмінієвих пористих сплавів (газарів) активно керувати процесом газовиділення водню при кристалізації та отримувати відливки з потрібною газовою пористістю.Item Контроль експлуатаційної стійкості валків гарячої прокатки з високохромистих чавунів та швидкорізальних сталей(НМетАУ, Дніпро, 2021) Полякова, Наталія Володимирівна; Бойко, Максим Миколайович; Журавльова, Світлана Валеріївна; Чеченєв, Володимир Андрійович; Іващенко, Валерій Петрович; Хричиков, Валерій ЄвгеновичUKR: Мета. Властивістю, що визначає якість матеріалів робочого шару прокатних валків вважається їх зносостійкістю. Однак в умовах гарячої прокатки на її стабільність можуть вплинути такі властивості як корозійна стійкість та термостійкість. Поширеними матеріалами для виконання прокатних валків гарячої прокатки є білий високохромистий чавун та швидкорізальна сталь, питанням термостійкості яких у сучасній літературі не приділено достатньо уваги. Метою роботи є контроль якості високохромистого чавуну та швидкорізальної сталі як матеріалів валків гарячої прокатки за рахунок оцінки їх термостійкості. Методика. Експериментальні зразки високохромистого чавуну марки ІЧХ16НМФТ та швидкорізальної сталі марок Р5М5 та Р6М5 були піддані термоциклуванню за режимом: 200 циклів нагрівання до 600°С та охолодження до 20°С. Після випробувань оцінювали зміни мікроструктури та мікротвердості структурних. Результати. Представлені результати дослідження схильності матеріалів, що застосовуються для виробництва прокатних валків, до руйнування, викликаного термічною втомою. Досліджено умови зародження та зростання тріщин термічної втоми у білому високохромистому чавуні, оцінені структурні зміни, що відбуваються при термоциклуванні. На поверхні зразків білого високохромистого чавуну у процесі випробувань було виявлено утворення макро- та мікротріщин термічної втоми. Мікротріщини проходять по евтектичних карбіду, значною мірою поширюючись на залишковий аустеніт, по межі розділу карбіду з продуктами розпаду аустеніту. На поверхні зразків швидкорізальної сталі в описаних умовах випробувань тріщиноутворення не спостерігалося. Внаслідок термоциклування білого високохромистого чавуну відбувається зниження мікротвердості металевої матриці, а мікротвердість евтектичного карбіду у порівнянні з вихідним литим станом збільшується. Мікротвердість структурних складових швидкорізальної сталі змінюється менш істотно. Наукова новизна. Встановлено механізм впливу термоциклуваня білого високохромистого чавуну та швидкорізальної сталі на зносостійкість робочого шару прокатних валків з цих матеріалів. Практична значущість. Відбувається зниження зносостійкості прокатних валків з робочим шаром з високохромистого чавуну в литому стані внаслідок термовтомного руйнування під час експлуатації в умовах гарячої прокатки. Підвищити термостійкість високохромистого чавуну ІЧХ16НМФТ можна, за рахунок застосування спеціальних методів термообробки, спрямованих на отримання бейнітної структури металевої матриці. Рекомендується враховувати показники термостійкості матеріалів прокатних валків гарячої прокатки як додатковий критерій контролю їх якості.